Double your space by parking two vehicles in the footprint of one parking stall
Unobtrusive and secure - the lift and lower vehicle are completely concealed
Aesthetically pleasing - canopy surface can be tiled to match surroundings
Multiple units can be installed side-by-side for use in condo's, offices etc.
Ideal for low-ceiling applications - use as 'vertical tandem parking' to save space
Safe, easy to operate
Made in America
A 2-deck vehicle parking system rigidly bolted together in the field of operation by a heavy-duty scissors style lift designed to lift (2) 5,000 lb. vehicles at the same time. The deck structure and lifting/synchronizing components are completely concealed below ground so there is no indication that a lift (or second car) is present when lowered. Bolt-together platforms and support members optimize handling during shipping and installation.
Standard Benefits and Features
Two (2) One-Piece, Structural Steel Parking Decks
(4) Steel Canopy Support Posts
Scissors Leg Stabilization
Adjustable Landing Legs
Maintenance Access Hatch
High Pressure Lifting Rams
Remote Hydraulic Power Unit
Pre-Plumbed Ram Piping
High Pressure Connecting Hose
Hydraulic Up-Travel Limiting Device
230V-1ph Motor Control Panel
"UP/DOWN” Operator P/B Station
Solenoid-Operated Down Valve
Key-Switch Security Lock-Out
Beveled Toe Guard Protection
Hydraulic, Free-Fall Arrest Devices on each Ram in Event of Line Rupture
Minimum 3:1 Structural Safety Factor
Over-Pressure Relief System
Details At A Glance:
Please note that we can
custom build your PhantomPark to meet your specific
Capacity: 7,000 lbs. Max Lifting (10,000 lbs. available-5,000 lbs. per platform for an addtitional cost of $1,500)
-(1) Vehicle on lower platform - 7,000 lbs. Max Static Holding
-(1) Vehicle on lower platform and one vehicle on upper canopy - 3,500 lb. max. capacity per platform.
Travel: 96" - 150"
Speed: 1.0 inches per second
Power Unit: REMOTE 5HP / 230 VOLT / 60 CYCLE / 1 PHASE
LOCATE WHERE CONVENIENT
Controls: (2) Maintained contact pushbutton stations with up, down, e-stop, and key lock out functions (NEMA-4). Suitable for wall mount. Pushbutton stations are shipped loose. 230/24 Volt transformer, motor starter, and overload protection mounted and pre-wired in control enclosure (NEMA-1). Shipped loose 24V control voltage.
All axle rollers and pivot points are equipped with lifetime-lubricated bearings.
Use SAE 5W30 Oil: Approximately (11) gallons required.
Lift to be painted machinery gray water based emamel.
Maintenance leg (not shown) is used to support unloaded lift for maintenance purposes only
Remote power unit approximate size: 18" x 24" x 30"
Run 3" diameter PVC pipe with long radius sweep elbows to provide a pipe chase for hydraulic hose to run from oil line recess to power unit location - by others
Maximum floor pressure - 160 PSI (approx.)
Scissor table traveling over 60" vertically must have personnel guarding installed around the perimeter. Enclosures and interlocked gates by others.
# of Rams
Bolt-Together Canopy Deck
Adjustable Wheel Locator
Special Supports for Sloped Floors
High-Speed Power Unit
Redundant Block Valve
230V-3ph Motor Control Panel
Emergency Stop Button Stations
Door Interlock Kits
Audible In-Motion Alarms
In-Motion Flashing Light
Electric Toe Sensors
Ti-Clad (salt water resistant) Paint
(No Bracing Required)
**Installation will be contingent on uninterrupted access to completed pit. Please note dimensions and weights in above description are designed for either new or remodel applications. Please review carefully which option best suits your existing conditions. Installation prices are subject to change, pending site inspection.
***Shipping is based on above weights, FOB Guthrie, OK 73044. Additional costs will be assessed for shipments outside the contiguous United States.